How to Replace a Tub in Your Bathroom
How to Replace a Tub in Your Bathroom
Blog Article
This article following next involving Tools You Need to Install a New Bathtub is really enjoyable. You should read it.
Setting up a bath tub isn't precisely brain surgery, however it does require strong plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old bath tub with a new one is also a reasonably challenging task. If the old tub is conveniently available, the task can relocate quickly; if you need to open a wall to eliminate the old tub and also position the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will require a helper to vacate the old bathtub and embeded in the new one. Make certain you have certified yourself for the work and are comfortable trying it. Instead of working with a professional to take control of a halfway-completed job, it is far better to think about using one before you start. Opportunities are you may need an expert plumber to make tube links.
This article will assist you mount a brand-new bathtub in your shower room if you have actually already purchased a new bathtub and also don't need to alter the plan of your previous water system pipelines.
Your devices and material list need to consist of the following:
Getting ready for the Installment
To start with, the sustaining frame supplied with the bath must be fitted (if called for) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to avoid stress on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be suited its final placement.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, activate the taps to drain any water remaining in the system. The procedure of eliminating the existing taps can be fairly bothersome because of the restricted accessibility that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. When the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old sealing substance.
Prior to moving on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Making use of the two wood boards under its feet, position the bathtub in the called for position. The wooden boards are handy in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The next goal is to make certain that the bathtub is leveled all round. This can be attained by checking the level and also changing the feet on the bath tub until the spirit level reviews degree.
To install faucets, fit the bottom of the furthest adaptable tap connector to the ideal supply pipe by making a compression sign up with; then do the very same for the other tap.
Activate the supply of water and also inspect all joints and brand-new pipework for leaks and also tighten them if required. Fill the tub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, deal with the bathroom paneling as described in the supplier's user's manual. Tiling and sealing around the bathtub needs to wait till the tub has been made use of at the very least when as this will resolve it right into its final position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washers are in area in between the tap and the sink. Safeguard the faucet in place with the maker offered backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous kind ought to be connected to the faucet finishes initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break a rigid seal, causing the water to pass through the wall surface between the bath and the tiling, bring about issues with wetness and also possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to securing, to permit the motion experienced when the tub is in usage. The sealer can split fairly early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise easily readily available on the market. It is recommended to fit the floor tiles making use of water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very enthusiastic about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I really hope you appreciated the new blog entry. Make sure you set aside a second to distribute this content if you appreciated it. I appreciate reading our article about Installing A Bathtub.
Request Service Report this page